EnduroSharp^® Scraper Blade & Holder Kit

 “Without Pneumatic Tool”

Part Number: ESSHK005

Kit contains 10 EnduroSharp^® Torlon^® Scraper Blades (2 each of Part Numbers: TSB-170, TSB-230, TSB-500, TSB-750, and TSB-1200), 1 each, “Pocket” Scraper Blade Holder (Part Number: ESSBH002), and 1 each, Standard Scraper Blade Holder (Part Number: ESHH003).

Deluxe EnduroSharp^® Torlon^® Gap Blade & Holder Kit

“With Pneumatic Tool”

Part Number: DEG007 

Kit contains 15 EnduroSharp^® Torlon^® Gap Blades (1 each of Part Numbers: TGB-75-75, TGB-75-16, TGB-75-25, TGB-10-75, TGB-10-16, TGB-10-25, TGB-12-75, TGB-12-16, TGB-12-25, TGB-17-75, TGB-17-16, TGB-17-25, TGB-23-75, TGB-23-16, and TGB-23-25), 1 each, Holder Adapter (Part Number: TGBA-001), 1 each, “Pocket” Scraper Blade Holder (Part Number: ESSBH002), 1 each, Standard Scraper Blade Holder (Part Number: ESHH003), and 1 each, Pneumatic Tool (Part Number: ESPT001).

EnduroSharp^® Torlon^® Gap Blade & Holder Kit

“Without Pneumatic Tool”

Part Number: ESGHK006

Kit contains 15 EnduroSharp^® Torlon^® Gap Blades (1 each of Part Numbers: TGB-75-75, TGB-75-16, TGB-75-25, TGB-10-75, TGB-10-16, TGB-10-25, TGB-12-75, TGB-12-16, TGB-12-25, TGB-17-75, TGB-17-16, TGB-17-25, TGB-23-75, TGB-23-16, and TGB-23-25), 1 each, “Pocket” Scraper Blade Holder (Part Number: ESSBH002), and 1 each, Standard Scraper Blade Holder (Part Number: ESHH003).

EnduroSharp® Surface Prep Kit

Part Number: ESNSP001

Adhesively bonded nutplates are increasingly being utilized in the manufacture of aerospace structures, with extensive use in securing removable maintenance access panels. When a nutplate fails, it can take an excessive amount of time to replace, resulting in undesirable aircraft down-time. Performance Plastics, in partnership with various suppliers, has devolved a suite of tools (EnduroSharp® Surface Prep Kit) to assist aircraft maintainers in quick removing the residual adhesive/sealant on the aircraft structure (remnants from a failed nutplate) and preparing the surface of the aircraft structure and the new replacement nutplate for bonding.

EnduroSharp® C-130 Prop Hub Adhesive Removal Kit

Part Number: ESC130001

EnduroSharp® C-130 Prop Hub Adhesive Material Removal Kit comes complete with case with custom foam inserts that contains: 2 each pneumatic tools, 1 each Class I, Division 2 flash light, 1 each contoured sharpening fixture (requires 120 – 180 grit abrasive paper, sold separately) and 4 each EnduroSharp® Torlon® Scraper Blades (2 each left hand and 2 each right hand).

Note: Required Left and Right Hand Prop Hub Abrasive Pads sold separately (Different Vendor)

EnduroSharp^® Pneumatic Tool

“For Torlon^® Scraper Blades and Torlon^® Gap Blades”

 (Torlon^® Gap Blades requires the use of the Torlon^® Gap Adapter)

Part Number: ESPT001

Pneumatic Removal Tool operates at a pressure of 90 psi (Max). For use with EnduroSharp^® Torlon^® Scraper Blades and EnduroSharp^® Torlon^® Gap Blade Adapter. Swivel Air Regulator fitting to prevent quick disconnect fitting galling and provide dial adjustment air flow regulation.

EnduroSharp^® “Pocket” Scraper Blade Holder

“For Torlon^® Scraper Blades and Torlon^® Gap Blades”

(Torlon^® Gap Blades requires the use of the Torlon^® Gap Adapter)

Part Number: ESSBH002

For use with EnduroSharp^® Torlon^® Scraper Blades and EnduroSharp^® Torlon^® Gap Blade Adapter.

EnduroSharp^® Standard Scraper Blade Holder (Standard Handle)

“For Torlon^® Scraper Blades and Torlon^® Gap Blades”

(Torlon^® Gap Blades requires the use of the Torlon^® Gap Adapter)

Part Number: ESHH003

For use with EnduroSharp^® Torlon^® Scraper Blades and EnduroSharp^® Torlon^® Gap Blade Adapter.

EnduroSharp^® Holder Adapter for Gap Blades (Gap Blade Adapter)

“For Torlon^® Gap Blades”

Part Number: TGBA-001     

Torlon^® Gap Blade Adapter requires the use of the EnduroSharp^® Pneumatic Tool, EnduroSharp^® “Pocket” Blade Holder, or EnduroSharp^® Standard Scraper Blade Holder.

EnduroSharp^® Scraper Blade Sharpener

“For Torlon^® Scraper Blades”

Part Number: ESSBS001

The EnduroSharp^® Scarper Blade Sharpener is a durable hand-held portable sharpening fixture used to sharpening the EnduroSharp^® Torlon^® Scraper Blades (TSB) tools (Part Numbers: TSB-170, TSB-230, TSB-500, TSB-750, and TSB-1200). The sharpener along with 120-180 grit sand paper, allows for quick sharping of the TSB tools, while maintaining the 25⁰/25⁰ asymmetrical 1/3-2/3 cutting edge. The simplistic compact design enables the operator to sharpen the TSB tool, while on the job site without the need for additional support items.

EnduroSharp^® Torlon^® Scraper Blade (TSB)

Part Numbers:

TSB-170, TSB-230, TSB-500, TSB-750, and TSB-1200

The TSB tools are supplied in EnduroSharp^® kits, Part Numbers: DES004 and ESSHK005. The TSB tools are designed to be used with the “Pocket” Scraper Blade Holder (Part Number: ESSBH002), Standard Scraper Blade Holder (Part Number: ESHH003), Pneumatic Tool (Part Number: ESPT001) and EnduroSharp^® Scraper Blade Sharpener (Part Number: ESSBS001).

EnduroSharp^® Torlon^® Scraper Blade (TGB)

Part Numbers:

TGB-75-75, TGB-75-16, TGB-75-25,  TGB-10-75, TGB-10-16, TGB-10-25, TGB-12-75, TGB-12-16, TGB-12-25, TGB-17-75, TGB-17-16, TGB-17-25, TGB-23-75, TGB-23-16, TGB-23-25

The TGB tools are supplied in EnduroSharp^® kits, Part Numbers: DEG007 and ESGHK006. The TGB tools are designed to be used with the EnduroSharp^® Holder Adapter for Gap Blades (Gap Blade Adapter) Part Number: TGBA-001. The Gap Blade Adapter is used with the “Pocket” Scraper Blade Holder (Part Number: ESSBH002), Standard Scraper Blade Holder (Part Number: ESHH003), Pneumatic Tool (Part Number: ESPT001) and EnduroSharp^® Scraper Blade Sharpener (Part Number: ESSBS001).

EnduroSharp^® Gap Filler Removal (GFR)-Discs/Blades

Part Numbers:

GFRD-25FDA55, GFRD-25FDS55, GFRD-25HDA55, GFRD-25HDS55, GFRD-2517R55, GFRD-2585R55, GFRD-2517S55, GFRD-2585S55

The EnduroSharp^® Gap Filler Removal (GFR)-Discs/Blades are a nonmetallic counterpart to the metallic multi-tool/oscillating disc/blades and can be used in a variety of electric (corded and battery powered) and pneumatic oscillating tools (NOT TO BE USED IN ROTARY TYPE GRINDERS). The (GFR)-Discs/Blades are available in eight configurations.

EnduroSharp^® Torlon^® Adhesive Reamer (TAR)

Part Numbers:

TAR-190, TAR-2155, TAR-250, TAR-2755, TAR-313, TAR-3375, TAR-3615, TAR-375, TAR-4005

The EnduroSharp^® TAR tools are nonmetallic multi-fluted straight walled reamers. The reamers have a hex drive mounting feature, allowing the reamer to be used with low rpm (200 rpm or less) battery powered screw driver, ratcheting screwdriver or the EnduroSharp^® Ratcheting T-Handle with Keyless Chuck (Part Number: ESRTH001)

EnduroSharp^® Ratcheted T-Handle

“For Use with Standard and Segmented Mandrels and Torlon^® Adhesive Reamers”

Part Number: ESRTH001     

The EnduroSharp^® Ratcheted T-handle is for use with mandrels (EnduroSharp^® Torlon^® Adhesive Cutters and abrasive pads) and the EnduroSharp^® Torlon^® Adhesive Reamers.

EnduroSharp^® Mandrel Torlon^® Adhesive Cutter (TAC) Kit

“For Use with Drill (600 RPM Max)”

Part Number: ESCKD008 

Kit contains 14 EnduroSharp^® Torlon^® Adhesive Cutters (5 each, Part Number: TACS-C-1, 5 each, Part Number: TACS-C-2, 2 each, Part Number: TACS-C-3 and 2 each, Part Number: TACS-C-4) 4 each Standard (non-segmented) Mandrels (1 each, Part Number: STAC-M-3, 1 each, Part Number: STAC-M-4, 1 each, Part Number: STAC-M-5, and 1 each, Part Number: STAC-M-6), 4 each Tertherable (segmented) Mandrels (1 each, Part Number: TTAC-M-3, 1 each, Part Number: TTAC-M-4, 1 each, Part Number: TTAC-M-5, and 1 each, Part Number: TTAC-M-6), 2 each Swivel Assemblies (1 each, Part Number: TACS-S-1 and 1 each, Part Number: TACS-S-2), and 1 each, Multi Wrench – 1/2″-7/8″-11/16″ (Part Number: TACW-W-1).

* The Torlon^® Adhesive Cutters can be used in a variety of electric (corded and battery powered) and pneumatic drills rated at 600 rpm or less (TORLON^® ADHESIVE CUTTERS ARE NOT TO BE USED OVER 600 RPM).

EnduroSharp^® Surface Preparation Tool (Andrews Tool) Mounted Torlon^® Adhesive Cutter (TAC) Kit

“For Use with Surface Preparation Tool (Andrews Tool Company), 500 RPM (Part Number: ATCP2L7-USPPR500-88R)”

Part Number: ESCKA009 

Kit contains 10 EnduroSharp^® Torlon^® Adhesive Cutters (5 each, Part Number: TACA-C-1, 5 each, Part Number: TACA-C-2) 4 each, Locating Buttons (1 each, Part Number: ATC00254D-191, 1 each, Part Number: ATC00254D-250, 1 each, Part Number: ATC00254D-312, and 1 each, Part Number: ATC00254D-375), 2 each, Quick Change Bushing (1 each, Part Number: ATC00483 and 1 each, Part Number: ATC00484), 1 each Torlon^® Adhesive Cutter Adapter (Part Number: ATAC-A-1), 1 each, Alignment and Spindle Lock Tool (Part Number:ATC00531), and 1 each, Multi Wrench – 1/2″-7/8″-11/16″ (Part Number: TACW-W-1).

* This kit is used with the pneumatic “Surface Preparation Tool” (Andrews Tool Company), 500 RPM (Part Number: ATCP2L7-USPPR500-88R).

EnduroSharp^® Torlon^® Adhesive Cutter (TAC)

Part Numbers:

TACS-C-1, TACS-C-2, TACS-C-3, TACS-C-4, TACA-C-1 and TACA-C-2

The TAC tools are supplied in EnduroSharp^® kits, Part Numbers: ESCKD008 (Part Numbers: TACS-C-1, TACS-C-2, TACS-C-3, and TACS-C-4) and ESCKA009 (Part Numbers: TACA-C-1 and TACA-C-2). The TACS tools are designed to be used with the Standard (non-segmented) Mandrels (Part Numbers: STAC-M-3, STAC-M-4, STAC-M-5, and 1 each STAC-M-6) and Tertherable (segmented) Mandrels (Part Numbers: TTAC-M-3, TTAC-M-4, TTAC-M-5, and TTAC-M-6) and an electric (corded and battery powered) and pneumatic drills rated at 600 rpm or less. The TAC tools are designed to be used with the Torlon^® Adhesive Cutter Adapter (Part Number: ATAC-A-1) and a pneumatic drill rated at 600 RPM or less.

EnduroSharp^® Multi Wrench – 1/2″-7/8″-11/16″

“Use with TACS and TACA Tools, Tertherable Mandrels, Torlon^® Adhesive Cutter Adapter and Andrews Tool”

Part Number: TACW-W-1     

The EnduroSharp^® Multi Wrench is supplied in the EnduroSharp^® kits, Part Numbers: ESCKD008 and ESCKA009. The wrench is used with TAC tools (Part Numbers: TACS-C-1, TACS-C-2, TACS-C-3, TACS-C-4, TACA-C-1 and TACA-C-2) as well as the Tertherable (segmented) Mandrels (Part Numbers: TTAC-M-3, TTAC-M-4, TTAC-M-5, and TTAC-M-6) and Torlon^® Adhesive Cutter Adapter (Part Number: ATAC-A-1).

EnduroSharp^® Swivel Assembly

“Use with TACS Tools and Tertherable Mandrels”

Part Numbers: TACS-S-1 and TACS-S-2

The EnduroSharp^® Swivel Assemblies are supplied in EnduroSharp^® Mandrel Torlon^® Adhesive Cutter (TAC) Kit, (Part Number: ESCKD008). The swivels are used with the Tertherable (segmented) Mandrels (Part Numbers: TTAC-M-3, TTAC-M-4, TTAC-M-5, and TTAC-M-6).

EnduroSharp^® Standard (non-segmented) Mandrels

Part Number: STAC-M-3, STAC-M-4, STAC-M-5, and STAC-M-6     

The EnduroSharp^® Standard (non-segmented) Mandrels are supplied in the EnduroSharp^® kits, Part Numbers: ESCKD008. The Standard Mandrels are used with TACS tools (Part Numbers: TACS-C-1, TACS-C-2, TACS-C-3, and TACS-C-4).

*The mandrels can be used in a variety of electric (corded and battery powered) and pneumatic drills rated at 600 rpm or less (MANDRELS ARE NOT TO BE USED OVER 600 RPM).

EnduroSharp^® Tertherable (segmented) Mandrels

Part Number: TTAC-M-3, TTAC-M-4, TTAC-M-5, and TTAC-M-6     

Each EnduroSharp^® Tertherable (segmented) Mandrels consists of 4 segments and are supplied in the EnduroSharp^® kits, Part Numbers: ESCKD008. The Tertherable Mandrels are used with TACS tools (Part Numbers: TACS-C-1, TACS-C-2, TACS-C-3, and TACS-C-4), and Swivel Assemblies (Part Numbers: TACS-S-1 and TACS-S-2).

*The mandrels can be used in a variety of electric (corded and battery powered) and pneumatic drills rated at 600 rpm or less (MANDRELS ARE NOT TO BE USED OVER 600 RPM).

EnduroSharp^® Locating Buttons

Part Numbers: ATC00254D-191, ATC00254D-250, ATC00254D-312, and ATC00254D-375

The EnduroSharp^® Locating Buttons are supplied in EnduroSharp^® Surface Preparation Tool (Andrews Tool) Mounted Torlon^® Adhesive Cutter (TAC) Kit (Part Number: ESCKA009). The Locating Buttons are used with the pneumatic “Surface Preparation Tool” (Andrews Tool Company), 500 RPM (Part Number: ATCP2L7-USPPR500-88R) in combination with the TACA tools (Part Numbers: TACA-C-1 and TACA-C-2), the Torlon^® Adhesive Cutter Adapter (Part Number: ATAC-A-1) and Quick Change Bushing (Part Numbers: ATC00483 and ATC00484).

EnduroSharp^® Torlon^® Adhesive Cutter Adapter

Part Numbers: ATAC-A-1

The EnduroSharp^® Torlon^® Adhesive Cutter Adapter is supplied in EnduroSharp^® Surface Preparation Tool (Andrews Tool) Mounted Torlon^® Adhesive Cutter (TAC) Kit (Part Number: ESCKA009). The adapter is used with the pneumatic “Surface Preparation Tool” (Andrews Tool Company), 500 RPM (Part Number: ATCP2L7-USPPR500-88R) in combination with the TACA tools (Part Numbers: TACA-C-1 and TACA-C-2).

*(ADAPTER IS NOT TO BE USED OVER 600 RPM).

EnduroSharp^® Combination Alignment and Spindle Lock Tool

Part Numbers: ATC00531

The EnduroSharp^® Combination Alignment and Spindle Lock Tool is supplied in EnduroSharp^® Surface Preparation Tool (Andrews Tool) Mounted Torlon^® Adhesive Cutter (TAC) Kit (Part Number: ESCKA009). The tool is used to realign the tool head and lock the spindle on the pneumatic “Surface Preparation Tool” (Andrews Tool Company), 500 RPM (Part Number: ATCP2L7-USPPR500-88R).